1 - Bulk Cloned-manufacture,factory,supplier from China

In order to meet the higher requirements of people at different levels of the consumer market for food, make full use of the existing food resources, and promote the sustainable and rapid development of the food industry, the food engineering technology and equipment industry must closely rely on scientific and technological progress.1.

TYPES OF CAT FOODCat food comes in a variety of shapes and textures, but can be broadly divided into four based on moisture content and manufacturing methods.*Heating foaming process: Using an extruder called an extruder, the mixed raw materials are heated and pressurized to 120 to 160 degrees.Characteristics and production methods of dry foodFEATUREDry food has the following characteristics.Moisture below 10%excellent preservationA nutritionally complete diet with high-efficiency and easily ingested nutrientsMoisture below 10%It has the lowest moisture content of the four and has a crunchy te

Nowadays, the population is large and the market demand is large. Most of them adopt advanced technology and use assembly line to produce food in bulk to achieve higher production efficiency.When it comes to the assembly line, the first reaction may be metallurgy, building materials, chemical, mineral, medicine and other industries. It is hard to think of using the assembly line to produce food at once. Some people even think that food such as to eat things, produced on the assembly line is not clean?There are still people who keep the habit of buying homemade food.

Series double screw extruder introduction:1, mainly by the feeding system, extrusion system, rotary cutting system, heating system, lubrication system, control system.2, extruder feeding system, main drive system, rotary cutting system all adopt frequency control, strong power, smooth operation, power saving.3, automatic lubrication, forced cooling, to ensure the safe operation of the extruder and prolong the life.4, screw alloy material, through special processing, high strength, wear resistance, increase the service life.5, according to different products, with different structure and length

Explain the daily operation and precautions of the extruder.(1) Precautions before starting:1. Check all parts, especially the connecting screws and anchor bolts of each section of the puffing chamber, the connecting bolts between the motor base and the frame, and the bolts between the puffing chamber and the frame, and there must be no looseness.2. Rotate the main shaft by hand, and there should be no rubbing sound in the puffing cavity at this time.3. Start the feeding auger, check its stepless speed regulation performance, and require normal operation.4.

What is a roller assembly line? As the name implies, it is to use roller conveyors as the transmission machinery of the whole assembly line, which can transport some flat-bottomed items along a horizontal angle or a smaller inclination angle. For parts such as boards, non-flat-bottomed items or flexible items can be transported by pallets or other flat-bottomed containers.Why use a roller conveyor as the transmission machinery of the assembly line? The reasons are as follows:1.

Twin screw extruder is developed on the basis of single screw extruder. Two screws are placed side by side in the barrel of the twin screw extruder. According to the meshing degree of the two screws can be divided into mutual meshing type and non-meshing type. According to the rotation direction of the two screw shafts, it can be divided into reverse rotation type and co-rotation type.(1) meshing twin screw: Because the meshing gap of the meshing screw is very small, the material has the ability of forced conveying, not easy to produce backflow, leakage phenomenon.

1. Before operating the corn equipment bulking machine, remove the head, movement, lead screw and other parts, clean them up, dry them and then install them.2. Idling for 1 to 2 minutes first when operating, put the raw materials into the feed mouth, not too fast, when the ring groove of the spiral shaft head is filled, stop feeding, friction preheating. Wait until the nose temperature rises and the pressure inside the cabin builds up before feeding.3. Feed should be continuous and uniform, material must be dry, must pay attention to.4.

After the processing of stirring machinery, it is necessary to carry out the shaping process, and there are many kinds of food shaping machinery, with different functions. According to different forming principles, food forming mainly has the following six methods.(1) The production of stuffing, such as bean buns, pies, dumplings, wontons and spring rolls.

Feed extruder is a single screw extruder. Mainly used for food puffing, livestock feed or used for puffing single raw materials, but also as a plant oil and drinking wine production of raw materials in the pre-place. Twin-screw extruding extruder, mainly used for the production and processing of high-grade aquatic products, pet materials, especially the processing of viscous materials.What are its characteristics?1.